Latest [Feb 26, 2024] Real Cisco 500-220 Exam Dumps Questions [Q36-Q54]

4.5/5 - (2 votes)

Latest [Feb 26, 2024] Real Cisco 500-220 Exam Dumps Questions

500-220 Dumps To Pass Cisco Meraki Solutions Specialist Exam in One Day (Updated 74 Questions)

NEW QUESTION 36
One thousand concurrent users stream video to their laptops. A 30/70 split between 2.4 GHz and 5 GHz is used.
Based on client count, how many APs (rounded to the nearest whole number) are needed?

NEW QUESTION 37
What is the best practice Systems Manager enrollment method when deploying corporate-owned iOS devices?

manual

Apple Configurator

Sentry enrollment

DEP

NEW QUESTION 38
What are two organization permission types? (Choose two.)

Full

Read-only

Monitor-only

Write

Write-only

NEW QUESTION 39
Refer to the exhibit.

Why does the end user complain of poor wireless performance?

Channel 48 utilization is at 84 percent.

Non-802.11 traffic of 18 percent indicates poor AP placement.

The client is connected to the secondary radio of the AP instead of the primary radio

The client is using a 20 MHz channel width to connect.

NEW QUESTION 40
Which information is used to calculate whether a WAN link has high usage?

data under Security & SD WAN > Appliance Status > Uplink > Live Data

total historical throughput of an uplink

total number of devices that are actively passing traffic

value under Security & SD WAN > SD WAN & Traffic Shaping > Uplink Configuration

NEW QUESTION 41
A customer requires a hub-and-spoke Auto VPN deployment with two NAT-mode hubs with dual uplink connections and 50 remote sites with a single uplink connection.
How many tunnels does each hub need to support?

100

104

NEW QUESTION 42
When wireless SSIDs are configured in Dashboard, which setting on the Access Control page affects the ability of a 2.4 GHz only client device from associating to the WLAN for the first time?

Content filtering

Bridge mode

802.11r

Dual band operating with Band Steering

NEW QUESTION 43
Refer to the exhibit.

During a Meraki AP deployment, the default SSID that the exhibit shows is broadcast. What causes this behavior?

An AP does not have a wired connection to the network.

An AP cannot connect to the default gateway.

An AP has never connected to the Meraki Cloud Controller.

An AP has Site Survey mode enabled.

NEW QUESTION 44
Refer to the exhibit.

What are the Loss and Average Latency statistics based on?

responses that the MX appliance receives on the connectivity-testing hostnames on the Insight > Web App Health page

responses that the MX appliance receives on the connectivity-testing IP addresses on the Security & SD- WAN > Firewall page

responses that the MX appliance receives on the connectivity-testing IP address that is configured on the Security & SD-WAN > SD-WAN & Traffic Shaping page

responses that the MX appliance receives on the connectivity-testing IP addresses on the Help > Firewall info page

NEW QUESTION 45
Drag and drop the settings from the left onto the available or non-available methods of applying a group policy to a Cisco Meraki MR access point on the right.

NEW QUESTION 46
What is out of scope when considering the Best practices for high-density wireless designs?

maximum beamforming

band selection

minimum bitrate

number of SSIDs

NEW QUESTION 47
Which Meraki Dashboard menu section is accessed to enable Sentry enrollment on an SSID?

Wireless > Configure > Access Control

Wireless > Configure > Splash page

Wireless > Configure > Firewall & Traffic Shaping

Wireless > Configure > SSIDs

NEW QUESTION 48
Refer to the exhibit.

Which outcome occurs when logging is set to Enabled?

Outbound flows are sent to a configured syslog server if a syslog sender is configured for flows.

The hits counter within this section is now enabled.

This firewall rule is now enabled.

Inbound flows are sent to a configured syslog server if a syslog server configured for flows.

NEW QUESTION 49
Which two actions can extend the video retention of a Cisco Meraki MV Smart Camera? (Choose two.)

enabling audio compression

installing an SSD memory extension

enabling motion-based retention

enabling maximum retention limit

configuring a recording schedule

NEW QUESTION 50
What occurs when a configuration change is made to an MX network that is bound to a configuration template?

The configuration change in the bound network is combined with the template configuration inside the template.

The more restrictive configuration is preferred.

The configuration change in the bound network overrides the template configuration.

The template configuration overrides the configuration change in the bound network.

NEW QUESTION 51
Which Meraki Dashboard menu section is accessed to enable Sentry enrollment on an SSID?

Wireless > Configure > Access Control

Wireless > Configure > Splash page

Wireless > Configure > Firewall & Traffic Shaping

Wireless > Configure > SSIDs

NEW QUESTION 52
Refer to the exhibit.

During a Meraki AP deployment, the default SSID that the exhibit shows is broadcast. What causes this behavior?

An AP does not have a wired connection to the network.

An AP cannot connect to the default gateway.

An AP has never connected to the Meraki Cloud Controller.

An AP has Site Survey mode enabled.

NEW QUESTION 53
What are two ways peers interact with ports that Auto VPN uses? (Choose two.)

For IPsec tunneling, peers use high UDP ports within the 32768 to 61000 range.

Peers contact the VPN registry at UDP port 9350.

For IPsec tunneling, peers use high TCP ports within the 32768 to 61000 range.

Peers contact the VPN registry at TCP port 9350.

For IPsec tunneling, peers use UDP ports 500 and 4500.

NEW QUESTION 54
A Cisco Meraki MX security appliance is trying to route a packet to the destination IP address of
172.18.24.12. Which routes contained in its routing table does it select?

Auto VPN route 172.18.0.0/16

static route 172.16.0.0/12

non-Meraki VPN route 172.18.24.0/24

directly connected 172.18.16.0/20