NEW QUESTION 40
Drag and drop the LISP components from the left onto the function they perform on the right. Not all options are used.

NEW QUESTION 41
Drag and drop the virtual components from the left onto their deceptions on the right.

NEW QUESTION 42
A customer wants to connect a device to an autonomous Cisco AP configured as a WGB. The WGB is configured properly: however, it fails to associate to a CAPWAP-enabled AP.
Which change must be applied in the advanced WLAN settings to resolve this issue?

NEW QUESTION 43
Exhibit.

Security policy requires all idle-exec sessions to be terminated in 600 seconds. Which configuration achieves this goal?

NEW QUESTION 44

Refer to the exhibit. Which configuration causes the traffic from PC-1 to the internet to use the link between CoreSW-1 and CoreSW-2 when both switches are up?

NEW QUESTION 45
Lab Simulation 8
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
– Refer to the Tasks tab to view the tasks for this lab item.
– Refer to the Topology tab to access the device console(s) and perform the tasks.
– Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
– All necessary preconfigurations have been applied.
– Do not change the enable password or hostname for any device.
– Save your configurations to NVRAM before moving to the next item.
– Click Next at the bottom of the screen to submit this lab and move to the next question.
– When Next is clicked, the lab closes and cannot be reopened.
Topology

Tasks
Implement GLBP between DISTRO-SW1 and DISTRO-SW2 on VLAN100 for hosts connected to ACCESS-SW1 to achieve these goals:
1. Configure group 30 using the virtual IP address of 192.168.1.254.
2. Configure DISTRO-SW1 as the AVG using a priority value of 110.
3. If DISTRO-SW1 suffers a failure and recovers, ensure that it automatically resumes the AVG role after waiting for a minimum of 15 seconds.

NEW QUESTION 46

Refer to the exhibit Drag and drop the snippets into the RESTCONF request to form the request that returns this response Not all options are used

NEW QUESTION 47
A company requires a wireless solution to support its mam office and multiple branch locations. All sites have local Internet connections and a link to the main office lor corporate connectivity. The branch offices are managed centrally. Which solution should the company choose?

NEW QUESTION 48

Refer to the exhibit. Which set of commands is required to configure and verify the VRF for Site 1 Network A on router R1?

NEW QUESTION 49
Refer to me exhibit.

Refer to the exhibit. Which configuration must be applied to R1 to enable R1 to reach the server at 172.16.0.1?

NEW QUESTION 50
Lab Simulation 12
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
– Refer to the Tasks tab to view the tasks for this lab item.
– Refer to the Topology tab to access the device console(s) and perform the tasks.
– Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
– All necessary preconfigurations have been applied.
– Do not change the enable password or hostname for any device.
– Save your configurations to NVRAM before moving to the next item.
– Click Next at the bottom of the screen to submit this lab and move to the next question.
– When Next is clicked, the lab closes and cannot be reopened.
Topology

Tasks
The operations team started configuring network devices for a new site. R10 and R20 are preconfigured with the CORP VRF. R10 has network connectivity to R20. Complete the configurations to achieve these goals:
1. Extend the CORP VRF between R10 and R20 using Tunnel0.
2. Protect Tunnel0 using the preconfigured profile
3. Configure static routing on R10 and R20 so that users in VLANs100 and 101 that belong to the CORP VRF are able to communicate with each other. Tunnel0 should be the only interface used to route traffic for the CORP VRF

NEW QUESTION 51
Drag and drop the snippets onto the blanks within the code to construct a script that brings up the failover Ethernet port if the primary port goes down and also shuts down the failover port when the primary returns to service. Not all options are used.

NEW QUESTION 52
When configuration WPA2 Enterprise on a WLAN, which additional security component configuration is required?

NEW QUESTION 53
Refer to the exhibit.

An engineer must configure static NAT on R1 lo allow users HTTP access to the web server on TCP port 80. The web server must be reachable through ISP 1 and ISP 2. Which command set should be applied to R1 to fulfill these requirements?

NEW QUESTION 54
Refer to the exhibit.

Refer to the exhibit. An engineer is using XML in an application to send information to a RESTCONF-enabled device. After sending the request, the engineer gets this response message and a HTTP response code of 400. What do these responses tell the engineer?

NEW QUESTION 55
Relet lo Ibe exhibit.

An ertgineer must modify the existing configuration so that R2 can take over as the primary router when serial interface 0/0.1 on R1 goes down. Whtch command must the engineer apply”

NEW QUESTION 56

NEW QUESTION 57
An engineer measures the Wi-Fi coverage at a customer site. The RSSI values are recorded as follows:

Which two statements does the engineer use to explain these values to the customer? (Choose two)

NEW QUESTION 58
Refer to the exhibit.

The administrator troubleshoots an EtherChannel that keeps moving to err-disabled. Which two actions must be taken to resolve the issue? (Choose two.)